Facebook




Banner
Banner Banner

+ Reply to Thread
Results 1 to 5 of 5

Thread: Volcano Box Manuals & Tutorials
              

  1. #1
    Administrator Ankit Verma's Avatar
    Group
    Administrator
    Join Date
    Jul 2010
    Location
    www.VaishnaviMobileCare.com
    Posts
    7,301
    Thanks
    1,270
    Thanked 796 Times in 591 Posts

    Default Volcano Box Manuals & Tutorials







    Volcano Box Manuals & Tutorials



    Ankit Verma

  2. #2
    Administrator Ankit Verma's Avatar
    Group
    Administrator
    Join Date
    Jul 2010
    Location
    www.VaishnaviMobileCare.com
    Posts
    7,301
    Thanks
    1,270
    Thanked 796 Times in 591 Posts

    Default

    How to do Work with MTK USB ?

    1st of all take phone and connect it.

    Make sure mobile is MTK.

    Click on DETECT TAB




    Now check which is your plug? For example I have plug like Motorola V3 with 5 pins up and 5 pin down

    For my example as I told you about my plug so I have to select my plug type its P-10c

    You can select from CABLE list your desire cable



    After select correct connector type . Select Charge pin from Detect Type list



    This will look like this



    So now click on detect and check which pin is VCC if in log window you see VCC pin number then just cancel it and if you don’t see then find it from charge pin windows


    How to find Charge pin ?

    From Detect Tab. Make sure you selected your correct mobile connector type and you selected Charge pin from Detect Type list. Now click on Detect button then press and hold power button.

    Now here you have two conditions

    A- You will see Vcc:Null
    B- You will see Vcc: 1 (or any pin)

    IF you have Condition “A” then you must do this

    After press and hold button you will see
    Vcc: null
    Gnd: 2 4 ( these can be any in my case my phone have 2 and 4 number pins GND)
    Short pins not detected.
    Detecting charge pin...

    Then this new Windows will be popup now you have to see it care fully.
    If will show current flow. If any pin take minor current or do not take any current this mean it’s not your charge pin.

    Which Pin take Good Current that pin will be your Charge pin or you can say VCC pin



    Keep in mind you have to press and hold power button until you not get your charge pin. As you can see in this picture needle is still at lower state so this is not your charge pin so simply click on NO and next pin will scan.

    More on NEXT post



    Ankit Verma

  3. #3
    Administrator Ankit Verma's Avatar
    Group
    Administrator
    Join Date
    Jul 2010
    Location
    www.VaishnaviMobileCare.com
    Posts
    7,301
    Thanks
    1,270
    Thanked 796 Times in 591 Posts

    Default




    When you see your needle Rise like this…. This will your Charge pin Simply Click on YES.

    After you select PIN number 10 as your charge pin as you can read top of this window for pin number detection. It will ask you would like to stop charge pin scan or continue . simply click on NO




    From Log window it will show like this
    Vcc: null
    Gnd: 2 4
    Short pins not detected.
    Detecting charge pin...
    Detecting 1 pin,Current: 0mA, Max: 0mA, Waiting-Time: 6s
    Detecting 3 pin,Current: 0mA, Max: 0mA, Waiting-Time: 1s
    Detecting 5 pin,Current: 0mA, Max: 0mA, Waiting-Time: 1s
    Detecting 6 pin,Current: 13mA, Max: 17mA, Waiting-Time: 1s
    Detecting 7 pin,Current: 0mA, Max: 0mA, Waiting-Time: 1s
    Detecting 8 pin,Current: 13mA, Max: 17mA, Waiting-Time: 1s
    Detecting 9 pin,Current: 0mA, Max: 0mA, Waiting-Time: 1s
    Detecting 10 pin,Current: 107mA, Max: 202mA, Waiting-Time: 9s
    Charging pin:10




    More on Next Post



    Ankit Verma

  4. #4
    Administrator Ankit Verma's Avatar
    Group
    Administrator
    Join Date
    Jul 2010
    Location
    www.VaishnaviMobileCare.com
    Posts
    7,301
    Thanks
    1,270
    Thanked 796 Times in 591 Posts

    Default

    IF you have Condition “B” you will see from log window

    Vcc: 1
    Gnd: 2 5
    Short pins not detected.
    >>Detecting charge pin...

    Then no need to find Charge pin just PRESS cancel from charge pin detecting windows

    Now Check from pinout selector is VCC is set to any pin ?
    If vcc set to any pin then good other wise set vcc pin to your desire pin which we find from above



    For my Example there is no any VCC set to any pin so I have to do manually how to do it ?



    Just put and drag on your desire pin

    After all of this your pin out selector look like this



    Till now we find Charge pin and GND now its ready for next setup

    Now from Detect Type Click on Mstar Boot Find



    Like this you can see. Click on Mstar (Do Find Boot) its very important cause if it find then you don’t need to find boot key from mobile key board


    When you select Mstar ( DO FIND BOOT) click on DETECT and PRESS and HOLD POWER BUTTON

    After some time it will show like this and set automatically BOOT pin. As it detect boot pin just release power button




    More on Next Post



    Ankit Verma

  5. #5
    Administrator Ankit Verma's Avatar
    Group
    Administrator
    Join Date
    Jul 2010
    Location
    www.VaishnaviMobileCare.com
    Posts
    7,301
    Thanks
    1,270
    Thanked 796 Times in 591 Posts

    Default







    After its detect boot pin now you have to click on SET PINOUT and press power button

    When you press power button it will ask you for Drivers. MTK USB driver already in your Installer so just Brows C:\Program Files\FuriouS TeaM\VolcanoBox\Drivers\Phone Drivers\MTK_usb ( Default path)
    And select folder if you use XP then give Drivers from XP if you are on win7 then give Drivers from win7 folder

    After installing Drivers click on set pinout with doing any thing It will show like this




    Now you are ready to do work

    In this stage a little trick

    After doing all this click on SET PINOUT and you have to press and hold power button till you not start any operation
    For example if you want to FORMAT or READ FLASH or WRITE FLASH. After doing all above when you press SET PINOUT you have to press and hold power button then click on mtk tab and select operation like read flash or write flash or format and UNTICK AUTO DETECT PINOUT and click on RUN when its start downloading then you can release power button. This is must you have to do other wise you can’t do format or read flash or write flash .

    Here is Final RESULTS



    Complete Procedure




    Ankit Verma

+ Reply to Thread

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Visitors found this page by searching for:

volcano box tutorial

how to use volcano box

volcano box

volcano box video tutorial

tutorial volcano box

volcano tool

volcano box user manual

volcano box manual

step by step nginstal box volcanohttp:www.gsmindore.comvolcano-box4714-volcano-box-manuals-tutorials.htmlvolcano box user guidevolcano box how to usevolcano box tutorialstutorial instal volcano boxhow to install volcano boxvideo tutorial volcano box volcano tutorialvolcano box setuptutorial box volcanomanual de volcano boxmanual volcano boxvolcano toolstutorial volcanotutorial vulcano boxvolcano box vcc null

Members who have read this thread : 17

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts